Is my USDT lost after OUT_OF_ENERGY?
No. A TRON transaction either runs to the end or is rolled back. When the USDT contract runs out of Energy halfway, every change it made is undone, so the USDT balance on both wallets stays as it was. The transaction is still recorded on the blockchain, and the network keeps what it charged for the work done: the TRX burned and any Energy used.
Don't send the same transfer again yet.Without fixing the cause it will fail the same way and burn more TRX. Renting Energy now doesn't refund the failed attempt either; it only helps the next one.
Read the receipt on TronScan first
Open the transaction in your wallet's history and tap through to TronScan, or paste the transaction ID into tronscan.org. Five fields tell you almost everything. Here is a typical failed receipt, made up for illustration:
- Result
- FAILED · OUT_OF_ENERGY
- Owner address
- TQ5nW3…8k2Wd
- Contract
- USDT (TR7NHq…Lj6t), transfer to TNew4x…pR1a
- Energy usage
- 115,000 = 65,000 delegated + 50,000 burned
- Fee limit
- 5 TRX, all of it burned
- Bandwidth
- 345, free daily quota
- Token transfers
- None
- Result.
OUT_OF_ENERGYmeans the contract stopped because it ran out of Energy. Anything else needs a different fix; see errors that look similar. - Owner address is the wallet that sent the transfer. Rented Energy only helps if it was delivered to this address.
- Energy usage shows what was available: 65,000 rented Energy plus 50,000 bought by burning TRX. Not enough: the recipient had no USDT, so the transfer needed about 130,285.
- Fee limit is the most TRX the transfer may burn. Burning stopped at 5 TRX even though the wallet had more.
- Token transfers: none. Proof the USDT didn't move.
7 causes of OUT_OF_ENERGY, and how to fix each
No Energy, and too little TRX to burn
How to tell: Energy usage shows only burned Energy, and the wallet's TRX balance is now close to zero.
Fix: rent Energy to the sending wallet, or add TRX. A transfer with no Energy can burn about 6.50 TRX, or 13.00 TRX to a new recipient.
Energy went to the wrong address
How to tell: the rental shows delivered, but the owner address on the receipt is a different wallet. Often the Energy was sent to the recipient instead of the sender.
Fix: rent to the address that sends the USDT. The recipient never needs Energy to receive.
The rental expired or was already used
How to tell: the transfer was signed after the rental period ended, or an earlier transfer used the Energy first.
Fix: rent again and send within the rental period. One 65,000 rental covers one typical transfer; used Energy only refills gradually over 24 hours.
The recipient had no USDT, so 65K wasn't enough
How to tell: 65,000 Energy delegated, Energy usage above 65,000 and the recipient's USDT balance is 0.
Fix: a first USDT transfer to a wallet needs about 130,000 Energy. Check the recipient before you rent. See 65K vs 130K.
The fee limit was too low
How to tell: TRX burned equals the fee limit exactly, while the wallet still holds TRX.
Fix: raise the fee limit if your wallet lets you, or cover more of the Energy with a rental so less needs burning. Every missing unit of Energy needs 100 sun (0.0001 TRX) of limit.
You signed before the Energy arrived
How to tell: the rental was confirmed seconds after the failed transaction's time.
Fix: wait until the delivery shows on the sending address, then sign. Delivery usually takes seconds.
The contract needed more than the estimate
How to tell: Energy usage is a little above what you rented, and none of the causes above apply.
Fix: the USDT contract's Energy use can shift with network conditions. Keep a margin, use your wallet's latest estimate, or rent the next size up.
Fix it in this order
- Check the transaction status
If it's still pending or already succeeded, don't create a duplicate transfer.
- Confirm the error is OUT_OF_ENERGY
Other errors need their own diagnosis; see errors that look similar.
- Check the sending wallet's resources
Confirm the rental was delivered to the same address that sent the USDT, and that it's still active.
- Get a fresh estimate for the recipient
If more Energy is needed, request a new quote for a sufficient amount. Check Bandwidth too: after 600 free a day, 345 Bandwidth costs 0.345 TRX.
- Review the fee limit and activation
If your wallet shows a fee limit, make sure it covers any Energy that might still burn. A wallet that has never received TRX must be activated before it can send.
- Then send a new transfer
Only after the cause is fixed. Energy spent by the failed transaction isn't restored by a later rental.
Errors that look similar
| What you see | What it usually means | First thing to check |
|---|---|---|
REVERT | The contract refused the transfer, for example not enough USDT or a restricted address | The USDT balance and the recipient address |
| Not enough Bandwidth or TRX | The wallet couldn't pay for the transaction's Bandwidth | Keep at least 0.35 TRX, or wait for free Bandwidth to refill |
| Account not found / inactive | The sending wallet has never been activated | Activate it with a small TRX deposit |
| Transaction expired | It was signed but not broadcast in time | Nothing was charged; sign it again |
Wallets word these differently. TRON's smart-contract error reference and fee-limit guidance list the exact codes. Renting Energy is not a fix for every failed transfer.
How to avoid OUT_OF_ENERGY next time
- Check the recipient first. The calculator tells you whether to rent about 65,000 or 130,000 Energy.
- Rent to the sender and wait until the Energy shows on that address.
- Send within the rental period. A 1-hour rental is for a transfer you send now.
- Keep a small TRX buffer for Bandwidth and small shortfalls.
- Read your wallet's final estimate before signing. If it still shows TRX being burned for Energy, something is missing.